{"product_id":"frasschablone-mit-nut-und-schlitz-mit-zwei-aluminium-schienen-fur-kantenfrasen","title":"Router template with groove and slot with two aluminum rails for edge routing","description":"\u003ch3\u003eStop fighting a wandering router: cut grooves and slots exactly where you marked them\u003c\/h3\u003e\u003cp\u003eFreehand routing is where good projects go off the rails. This groove and slot jig holds your trim router between two aluminum guide rails, keeps the bit on an exactly parallel line, and lets you cut clean grooves, channels, and slots for hidden fasteners along the edge of any board without wobble, without tear-out, and without rework.\u003c\/p\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0852\/7744\/2314\/files\/ccg-24072-desc-1.webp?v=1792123533\" alt=\"Router Mortise \u0026amp; Slot Jig with Twin Aluminum Rails for Trim Routers\" loading=\"lazy\"\u003e\u003ch3\u003eMisaligned grooves are an setup problem, not a skill problem\u003c\/h3\u003e\u003cp\u003eYou measured, you marked, and you started the cut cleanly. Two inches later, the router pulled, the bit drifted off line, and now a workpiece you can’t replace has a sloppy groove. Compact trim routers don’t have a real edge guide built in, and most add-on guides are loose-fitting plastic that shifts as soon as you start pushing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e➤ Dual aluminum rails lock in the cut line:\u003c\/strong\u003e Two anodized aluminum guides clamp tightly to both sides of the workpiece so the router runs exactly parallel from start to finish, without drifting and without skating across the grain.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e➤ Four knurled screws set the slot position:\u003c\/strong\u003e Tighten the knurled thumb screws by hand to fine-tune the bit’s distance from the edge. Cut centered grooves, offset channels, or fastening slots with the same jig, without shims and without calculations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e➤ Clear acrylic base for a full view of your layout line:\u003c\/strong\u003e See your pencil line, the bit, and your stop marks through a 1\/4-inch acrylic plate and plunge exactly where you intended every time.\u003c\/p\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0760\/3549\/0042\/files\/cc-imgtx-87a5c71dd3a29a2d-de.png?v=1792360715\" alt=\"Router Mortise \u0026amp; Slot Jig with Twin Aluminum Rails for Trim Routers\" loading=\"lazy\"\u003e\u003ch3\u003eFits any 65mm trim router, with no drilling or modifications\u003c\/h3\u003e\u003cp\u003eIf your compact router body diameter is between 63.5mm and 65mm, which covers most Makita, DeWalt, Bosch, Milwaukee, and Ryobi hand and trim routers, you slide the jig on, lock it in place, and you’re ready to cut in under two minutes. The included 1\/4-inch shank straight bit (11mm cutting diameter, 30mm cutting length) is factory-suited for hinge mortises, Lamello-style slots, and 8mm\/10mm channels for hidden fasteners.\u003c\/p\u003e\u003cp\u003eOther guides flex when you apply pressure. These aluminum rails sit flush, grip the workpiece firmly, and let you lean into the router without the jig running off the edge.\u003c\/p\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0760\/3549\/0042\/files\/cc-imgtx-aa5d3d697c135708-de.png?v=1792360721\" alt=\"Router Mortise \u0026amp; Slot Jig with Twin Aluminum Rails for Trim Routers\" loading=\"lazy\"\u003e\u003ch3\u003eWhy DIYers and pros replace their old edge guides\u003c\/h3\u003e\u003cp\u003eWoodworkers who had given up on freehand groove cutting and used to reach for a chisel for every hinge set this jig once and make joints they would normally pay a cabinet shop to produce. As one customer put it: \"I wish I’d bought this before starting the kitchen. Took me from six bad grooves to zero.\"\u003c\/p\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0760\/3549\/0042\/files\/cc-imgtx-bf39e7e06bb04913-de.png?v=1792360717\" alt=\"Router Mortise \u0026amp; Slot Jig with Twin Aluminum Rails for Trim Routers\" loading=\"lazy\"\u003e\u003ch3\u003eCuts you used to avoid, finished in minutes\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003e✓ Repeatable hinge mortises:\u003c\/strong\u003e Set the rails once and cut every door in the run identically, without switching templates and without measuring twice per door.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e✓ Hidden-fastener slots done right:\u003c\/strong\u003e Cut clean channels for Z-clips and panel connectors for ready-to-assemble furniture and edge-joined panels - joints that used to require an expensive specialty jig.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e✓ Edges that look shop-made:\u003c\/strong\u003e The anodized aluminum rails do not bend, the knurled steel thumb screws stay tight even under vibration, and the acrylic base shrugs off impacts and resin.\u003c\/p\u003e\u003ch3\u003eHow to use it: three steps to your first cut in under two minutes\u003c\/h3\u003e\u003cp\u003eStep 1: Set your trim router into the clear acrylic ring and hand-tighten the side clamp until the router body is secure.\u003c\/p\u003e\u003cp\u003eStep 2: Slide the dual aluminum rails against both sides of the workpiece and tighten the four knurled screws. The bit now runs on a fixed line.\u003c\/p\u003e\u003cp\u003eStep 3: Power on, plunge to depth, and guide the router from one stop mark to the other. Lift it off and you have a groove that fits right the first time.\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0760\/3549\/0042\/files\/cc-imgtx-36b169f12a344e6b-de.png?v=1792360705\" alt=\"Router Mortise \u0026amp; Slot Jig with Twin Aluminum Rails for Trim Routers\" loading=\"lazy\"\u003e\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eGroove and Slot Jig\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eFreehand \/ Chisel\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eGeneric Plastic Edge Guides\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRuns exactly parallel along the edge thanks to dual aluminum rails\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e❌ Wanders, depends on a steady hand\u003c\/td\u003e\n\u003ctd\u003e❌ Single rail, flexes under pressure\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eCuts grooves and hidden-fastener slots with a single setup\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e❌ Different tool for every cut\u003c\/td\u003e\n\u003ctd\u003e❌ Grooves only, no fastening slots\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFits 63.5-65mm trim routers, including Makita, DeWalt, Bosch, and Milwaukee\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e❌ Not applicable\u003c\/td\u003e\n\u003ctd\u003e❌ Often router-specific and locked to one brand\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eTechnical specs: what you actually need to know\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Dual-function groove and slot jig\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunctions:\u003c\/strong\u003e Edge routing and slot cutting, plus cutting slots for hidden fasteners\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRouter compatibility:\u003c\/strong\u003e 63.5-65mm (2.5\", 2.56\") housing diameter, fits most compact, trim, and hand routers\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBase plate dimensions:\u003c\/strong\u003e 165mm × 104mm × 36mm (6.5\" × 4.09\" × 1.42\")\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded bit:\u003c\/strong\u003e 1\/4\" (6.35mm) shank straight bit, 11mm cutting diameter, 30mm cutting length, 60mm overall\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConstruction:\u003c\/strong\u003e Anodized aluminum rails, clear acrylic sleeve, knurled steel thumb screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eYour questions, answered\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWill it fit my specific router?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eIf your trim or hand router has a housing diameter between 63.5mm and 65mm, which covers the Makita RT0700\/RT0701, DeWalt DCW600\/DWP611, Bosch Colt PR20EVS, Milwaukee 2723-20, and most Ryobi hand routers, it slides right in. If you are unsure, measure your housing diameter before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat cuts can I make with it?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eHinge mortises, Lamello- and Domino-style slots, edge grooves for shelf supports, channels for sliding tracks, and slots for invisible Z-clip fasteners on ready-to-assemble furniture panels. The included 11mm bit covers the most common slot widths; swap it for other 1\/4\" shank straight bits for narrower or wider cuts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs it strong enough for hardwood, or just pine and plywood?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eThe aluminum rails and steel thumb screws handle oak, walnut, maple, and hardwood plywood without flexing. In dense hardwoods, you should make two passes in depth to keep the bit cool and the cut clean.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow long does the first setup take?\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eInsert the router, clamp the rails to the workpiece, set the four knurled screws, and plunge to depth. Once you have done it twice, it takes under two minutes from box to first groove.\u003c\/p\u003e\u003ch3\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0760\/3549\/0042\/files\/cc-imgtx-117eaeccc85ab1ec-de.png?v=1792360703\" alt=\"Router Mortise \u0026amp; Slot Jig with Twin Aluminum Rails for Trim Routers\" loading=\"lazy\"\u003e\u003c\/h3\u003e\u003ch3\u003eBuilt like the jig you would make yourself if you had a CNC and a free day\u003c\/h3\u003e\u003cp\u003eIf this jig does not give you cleaner, straighter grooves than your current setup on your very first project, send it back for a full refund. There is no restocking fee, and you do not have to prove how you cut your test pieces.\u003c\/p\u003e","brand":"Haus of Mode","offers":[{"title":"A single slotted plate","offer_id":59781464817989,"sku":"10670274117898-53919844499722","price":35.95,"currency_code":"EUR","in_stock":true},{"title":"Slotted plate + transparent cover + router bit","offer_id":59781464850757,"sku":"10670274117898-53919844532490","price":53.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0765\/0125\/4469\/files\/cc-imgtx-87a5c71dd3a29a2d-de.png?v=1792361030","url":"https:\/\/hausofmode.de\/en-eu\/products\/frasschablone-mit-nut-und-schlitz-mit-zwei-aluminium-schienen-fur-kantenfrasen","provider":"Haus of Mode","version":"1.0","type":"link"}